Calibration and Test Kits
1 Watt Calibrated Attenuator Set
Radiall offers a high quality 1 Watt Calibrated Attenator Kit R-414799-125, N Connectors, DC to 18 GHz, 3, 6, 10 and 20 dB, boxed, complete with a certificate of calibration qualifying both Attenaution and VSWR values from DCT to 18 GHz in 1 GHz Steps.
Pasternack PE310-KIT VNA Test Cable Set, flexible pair of test cables, 50 Ohm, DC to 26.5GHz, End A 3.5mm NMD Connector, End B interchangeable Connector heads configurable for DUT applications that require Precision 7mm(PC-7), N, 3.5mm, SMA or 2.92mm Connectors.
3.5mm, 26.5GHZ, VNA Calibration Kit
Pasternack’s 3.5mm Standard Calibration kit (PE5500-KIT) is designed for use with a broad range of vector network analyzers (VNAs) that utilize a Short-Open-Load calibration technique. With this kit you can make error-corrected measurements of devices supplied with either 3.5mm or SMA connectors from DC to 26.5 GHz. This kit contains both Male (Plug) and Female (Jack) connector interfaces to perform full Two-Port error corrections.
Features include: Broad VNA Coverage, including Agilent & Anritsu, Open, Short, Fixed Broadband Load Configurations, DC to 26.5 GHz & In-Series Phase Matched Adapters available.
Type N, 18GHz VNA Calibration Kit
Pasternack’s vector network analyzer calibration kit with N-Type connectors (PE5501-KIT) is designed to calibrate a broad range of VNA models. VNA
calibration kit is designed for equipment that utilizes a short open load calibration technique. With this N type vector network analyzer calibration kit, you can make error corrected measurements of test devices supplied with N type connectors from DC to 18 GHz.
The Pasternack vector network analyzer calibration kit contains both male plug and female jack N connector interfaces. Using this VNA calibration kit from Pasternack Enterprises you can perform full two port error corrections.
Vector Network Analyzer Calibration Kit Features: Broad VNA Coverage, Including Agilent & Anritsu, Open, Short, Fixed Broadband Load Configurations, DC to 18 GHz VNA Calibration Kit Range with In-Series Phase Matched Adapters available.
Open & Short Circuits
Pasternack has an excellent range of Male and Female Open Circuits together with a selection of Male and female Short circuits for test applications.
RF Testing & Calibration Accessories
In addition, as part of Pasternack’s off the shelf range, they offer broadband male and female test loads.
Pasternack’s 3 port calibration tool can make error corrected measurements of devices supplied with 3.5mm connectors. Also called “Bones”, this calibration tool is very effective when needing to make instrument calibrations. Pasternack 3.5mm female 3 port calibration tool is great for the field because it is lightweight and portable.
Our 3 port tool for calibration has female (jack) connector interfaces to perform short, open, and load measurements on the device you are evaluating. PE5510 calibrator tool for the field is fully compatible with Anritsu SiteMaster™ analyzer and other handheld cable and antenna analyzers.
PE5510 – 3.5mm Female, DC to 26.5 GHz
PE5511 – 3.5mm Male, DC to 26.5 GHz
PE5512 – N Female, 50 Ohms, DC to 6 GHz
PE5513 – N Male, 50 Ohms, DC to 6 GHz
PE5514 – 7/16 Female, 50 Ohm, DC to 6 GHz
PE5515 – 7/16 Male, 50 Ohms, DC to 6 GHz
.
Military Circular Connectors
Rojone has been sourcing and supplying Military Circular Multipin connectors since we established in 1981. In addition, Rojone is able to custom manufacture cable looms to your specifications within our Ingleburn NSW plant.
Download Mil Circular Series catalogues below
Mil-C-5015 Series Connectors
Developed in 1939, the Mil-C 5015 series is one of the oldest connector ranges still on the market today. This series is classed as a general duties connector, commonly referred to as power connectors. The contact selection accommodates a range of wire sizes #0 to #16 American wire gauges, with 6 operating voltages.Main Characteristics – Material & Finish Aluminium alloy, olive drab.
Crimp & Solder versions are available, standard connector is screw/spin coupling although the range, part numbers suffixed with the letter “B” is a specialised 3 Lug bayonet coupling version. This range is environmentally resistant with a temperature range -55 to +125 Degrees C. A full range of dust caps, special contacts and back shells are also available.MIL-C-26482 Series 1 & 2 Connectors
Series 1 MS3100 to MS3119 are solder type, cost effective, general duty connectors. Series 2 are crimp, rear release connectors, ideal for more demanding applications requiring a higher temperature range of 175 to 200 Degrees C, fluid resistance, including the W Class with 500 hours salt spray. There are a range of conductive & non-conductive finishes as well as hermetic sealed options.MIL-C-38999 Series 1, 2, 3 & 4 Connectors
The Mil-C-38999 series of connectors were designed for both performance & mechanical robustness to meet a variety of demanding applications; Military, Aerospace, Ballistic Missile & Weapon Systems, and Marine Equipment.Common features applied to the D38999 family are compact size & weight, common mounting cut-outs, standard insert arrangements. Contacts, crimp tools, insertion/removal tools, sealing plus and assembly techniques are all standard across the whole MIL-C-38999 connector series.
The D38999 series offers excellent EMI Shielding up to 90dB, high durability with over 500 mating cycles, sine & random vibration specifications, firewall & scoop proof options.Series 1 & 2 are Bayonet coupling connectors, with Series 3 & 4 being screw coupling mating versions.
Multi Core/Multi Pin Cable Assemblies
With over 30 years of manufacturing cable assemblies, Rojone is one of the most consistent & experienced assembly companies in Australia today.
Rojone is able to work with you to create a custom assembly, with in-house CAD services to develop your specific requirement or just competitively build to print.
Rojone has a suite of automated stripping, crimp tool & gauges. We have a range of Vector Network & spectrum Analyzers, and Environmental test chamber -40C to +100 C as well as in-house plastic injection capabilities for both standard & specialized over molding.
Technicians are all IPC/WHMA-A-620A certified specialists for Cable & Wire Harness Assemblies.
We have proudly supplied product into many varied industries both in Australia & abroad, including
Defence contractors & aerospace applications, demanding mining, vehicle and survey & construction applications, Telecommunications & Radio Communications applications.
RRU AISG Multi-Wire Cable (Model: CA-RET-8P-9P-500)
An RRU AISG multi-wire cable is 5 m (16.4 ft.) long. It connects an RRU and an RCU to transmit control signals from a base station to the RET antenna. When the RRU is connected to the RET antenna, an AISG multi-wire cable transmits RS485 signals.
Pasternack Fibre Optic Cable Assemblies
Pasternack offer an excellent range of ready made, stock, Fibre Optic cable assemblies, both
singleand multi mode cables terminated to standard ST, FC, LC MTRRJ, VF45 Simplex & Duplex connector.
Pasternack Fibre Optic Cable Assemblies – Pasternack has just introduced a range of 10GB Fibre Optic Cables assemblies backwardly compatible to existing network equipment. These FO cables provide close to triple the bandwidth of traditional 62.5/125 multimode fibre. 10 Gigabit is rated for distances up to 300 metres using 850nm vertical cavity surface emitting lasers (VCSELs).
Pasternack 10GB Fibre Optic Cable Assemblies
Pasternack also offers a range of stock line Fibre Optic cables, connectors & accessories. Please feel free to browse the Pasternack website, or contact sales@rojone.com.au if you would like a Pasternack catalogue posted to you.
Coaxial Assemblies
Presentations
Rojone has been manufacturing and selling high quality RF & microwave coaxial cable assemblies since 1981. We offer a comprehensive range of locally manufactured assemblies, as well as high-performance, low-loss, extreme- and military-grade products from Times Microwave USA and Radiall France.
Brands & Products
Rojone Assemblies
Rojone Cable Assembly catalogue (1.5 MB)
Our Production is equipped with the latest test instruments, Vector Network & Spectrum Analysers (HP8720D, HP8753B, 8495E), a Thermoline Thermal Chamber for temperature cycling cables, auxiliary items such as precision Schleuniger 207 and their latest CS5400 cable stripping machines, inspection microscopes, pin depth gauges and automated test software.
Times Microwave
TMS is the expert in its field, providing high-performance RF & Microwave assemblies for the harshest of military, civil & test applications.
- SilverLine® – Low Cost, Flexible, High-Performance Test Cables.
- MilTech™ – Extreme Environments hermetically sealed, low-loss, low-VSWR, phase-stable, and lightweight options for airborne applications.
- Zero-DB – Zero Loss, integrated LNA for critical aircraft applications.
- SiO2 – Silicon Dioxide Extreme Environment military assemblies.
- Military Tactical Field Deployable Antenna Feeder cables – Designed to withstand the riggors of repeated reeling for harsh Environments.
- Heli-Foil – Low Loss High Performance Microwave Coaxial assemblies.
Radiall
Radiall offers a specialised range of RF & Microwave coaxial & multipin cable assemblies:
- Corrugate
- Flexible RG, KX, ECO, ECOX
- Flexible Ultra-Low Loss SHF
- Hand-Formable
- Semi-Rigid
- Space Qualified
- TestPro Bench Test
Pasternack
Pasternack offers an excellent commercial range of:
- Coaxial cable assemblies
- Patch Cords covering banana leads, alligator and spade leads
- Fibre Optic assemblies
L-com
L-com produces a range of High Performance Armoured Cable Assemblies that feature a stainless Steel Flexible Jacket. Built around a low-loss coax cable that works to a range up to 10 GHz, they are designed for use in the following applications;
- Harsh industrial environment
- High traffic production test systems
- Installations susceptible to rodent damage
Other Cables
Under construction
Multi Core Cables
GPS Repeaters
Rojone has been a leader in GPS repeating systems for many years. Our first commercial low cost system was developed in the early 90’s, refined over the years and is now in huge demand & sold throughout the world.
As a result of our commercial success, we were asked to develop a high performance, reliable L1/L2 system for the RAAF in Australia. This project has been a huge success, with many systems installed Australia wide. These repeaters offer many benefits not only in the maintenance area but keeping aircraft ready for rapid deployment.
L1 Commercial GPS Repeater Kit
The L1 Commercial GPS Repeater Kit is our low cost commercial L1 1575MHz repeater kit. Designed to simply bring GPS signals indoors cost effectively for test labs and vehicle garages, it is ideal for timing applications.
GPS L1/L2 Fixed Repeater System
The GPS L1 L2 Fixed Repeater Systems series was developed as a high performance L1/L2 GPS repeater system for the Australian Air Force. Specifically designed for permanent installation, it overcomes operational difficulties providing reliable dual band coverage anywhere needed.
The system features a highly sensitive active receive antenna capable of tracking satellites down to 5 degrees elevation, efficient TX antenna over 100dB RF blocking cellular, VHF & UHF radio frequencies. A high performance RF amplifier with high rejection filters for both L1 and L2. The repeater incorporates its own 110-240VAC power supply for quick & easy set up.
Portable, Compact L1/L2 Portable GPS Repeater System

Designed for the military however ideal for a range of Applications. This portable system was designed for rapid deployment, the system can be set up in under 20 minutes to provide L1/L2 GPS coverage to a variety of military & civilian vehicles including aircraft while under cover or inside hangars.
This self-contained system, weighs no more than 38 Kgs. The IP65 rated military designed case contains all the system Components to provide quick & reliable L1/L2 GPS coverage for up to 15 meters in radius.
The ROJ-140 system features a highly sensitive active receive antenna capable of tracking satellites down to 5 degrees elevation. It incorporates high performance RF amplifiers with high rejection filters for both L1 & L2. It boosts efficient TX Antenna, over 100dB RF blocking cellular, VHF & UHF radio Frequencies. Truly portable, it operates on battery power or can be connected Mains power and features auto power supply detection & low battery alarm.
Mobile L1/L2 GPS Repeater System – for Armoured Personnel Carriers (APC) Military Applications
Rojone has recently added a New Mobile L1/L2 GPS Repeater product to its already extensive family of commercial and military systems. The ROJ-150B kit is specifically designed for troop carrying mobile platforms such as APC’s (Armoured Personnel Carriers).
The ROJ-150 system, when installed, will re-transmit the GPS L1/L2 band signals within the enclosed vehicle to provide adequate coverage to maintain personal GPS receivers on equipment and man packs.
FAQ: Are GPS Repeaters permitted in Australia?
GPS repeaters can be legal in Australia, but some restrictions and regulations must be followed to ensure compliance with the law.
The Australian Communications and Media Authority (ACMA) regulates the use of GPS repeaters in Australia, and it is important to comply with their regulations to avoid fines or legal action. In general, GPS repeaters are only legal if they meet specific requirements, such as:
- They must be designed to receive and re-transmit GPS signals without causing harmful interference to other wireless services.
- They must be licensed by the ACMA and operated in compliance with the conditions of the license.
- They must not be used to interfere with or disrupt GPS signals used by emergency services, aircraft, or other critical applications.
It is also important to note that GPS repeaters that are not properly licensed or operated in compliance with the ACMA regulations can cause harmful interference to other wireless services and disrupt GPS signals, which can have serious consequences. Therefore, it is recommended to consult with the ACMA or a qualified professional before installing a GPS repeater in Australia.
Cellular Repeater CDMA, Next G
Information from ACMA
Mobile phone boosters/amplifiers, regardless of where they are intended to be used by third parties (i.e. not a mobile telecommunications carrier), are a prohibited device and cannot be legally used in Australia.
All radiocommunications transmitters operating in Australia, its territories and its territorial waters do so under the authority of an Australian Communications and Media Authority (ACMA) issued spectrum, apparatus or class license.
A mobile telephone booster/amplifier and/or repeater is a radiocommunications transmitter and therefore can only be operated in Australia under the authority of an ACMA issued radiocommunications license, or with the permission of the current licensees.
- The radio spectrum in which these mobile telephone booster/amplifiers and/or repeaters operate, is exclusively licensed to the mobile telephone carriers (including Telstra, Optus and Vodafone).
- There are no mobile telephone booster/amplifiers and/or repeaters licensed for use in Australia, with the exception of those operated by the mobile telephone carriers who may install and operate these or similar devices as part of their networks under their licenses.
- Third parties cannot be given licenses by the ACMA to operate mobile telephone booster/amplifiers and/or repeaters in this spectrum. You would need the permission of the licensees (the mobile telephone carriers.
There have been several instances where mobile telephone booster/amplifiers and/or repeaters have been imported into Australia from overseas and the subsequent use has resulted in interference to mobile telephone networks. ACMA has seized several of these devices and appropriate compliance enforcement action was taken under the Radiocommunications Act 1992.
Severe criminal penalties, including court imposed penalties up to $165,000.00 or 2 years imprisonment, exist under the Radiocommunications Act 1992 for the unlawful possession of and/or the use of these devices. Telecommunications carriers may also initiate civil legal action against users for any losses suffered due to the use of these devices the users may subsequently be able to take civil action against the suppliers.
Summary of mobile phone booster prohibition
You cannot legally use a booster or repeater for better mobile phone reception.
Reasons:
- A booster or repeater is classed as a transmitter.
- You need a licence to operate a transmitter.
- The booster would be re-transmitting in the same radio frequency spectrum covered by the Spectrum licences owned by the mobile service providers (the Carriers).
- You cannot legally transmit in the frequencies allocated to the carriers by their licences, without their permission.
Mobile phone boosters banned – Information for consumers:
http://www.acma.gov.au/theACMA/mobile-phone-boosters-banned-information-for-consumers
Alternatives:
Contact your mobile carrier (you mobile phone service provider) to ascertain if they are able to offer you any alternatives, or:
You might find the following alternatives suggested if you were to search on-line for solutions and information, depending on which is most suitable for your phone and situation:
- install a “car kit” for your home, or
- install an external antenna which is cable connected inside either directly to connector on the phone or via an inductive coupler if your phone is without provision for connection of an external antenna, or
- install a passive indoor antenna. Pick up some coaxial cable (enough to go from the outside of your home to the inside) and two antennas with coaxial connections from your nearest electronics store. Place your outside antenna in a location with a strong signal and run the cable into your home. Try running your cable through a window at first to make sure the passive antenna will help improve signal strength before you drill into your home. After connecting both the outdoor and indoor antennas check your signal strength, as it should be improved at this time.
You may still need to check with your Carrier or Service Provider (i.e. Telstra, Optus, 3, Vodafone, Virgin etc) to verify that these suggestions are acceptable under their Spectrum Licence conditions.
Rojone – GPS Product Guide
Rojone has a full range of GPS products, to download a copy of our GPS catalogue click on the link below.
Amplifiers
Rojone offers a range of in-house designed amplifiers specifically designed for unique applications and customer requirements.
Here are a selection of Rojone custom designed amplifiers for recently completed projects.
Low Noise Amplifiers
902-928 MHz, 18dB Gain, SMA LNA with Automatic Level Control – AMA-3121
902-928 MHz, 10dB Gain, SMA Power Amplifier – AMA-3122
1000-3000MHz, 15dB Gain, SMA Instrument LNA – AMA-3310-15S
1100 to 1300MHz, 17dB Gain, SMA LNA – AMA-3301-15-SMA
GPS Amplifier
AMA -061 Series GPS Amplifier & DC Feed L1 and L1/L2
Developed exclusively for GPS applications, Rojone’s Amplifiers and DC Feed are high performance devices designed to boost GPS signals for long range transmission or to overcome noisy environments. They can also be used as D Feeds for GPS antennas. The DC thru can be regulated or bypassed to the antenna for 5V systems.
Tower Top Amplifiers/Receivers
700-1000 MHz Tower Top Amplifiers by Sinclair Tech USA
TM4 Low-Loss Tower Top Amp/Receiver MulticouplerUHF & Tetra Tower Top Amplifiers by Sinclair Tech USA
TM3 Low-Loss Tower Top Amp/Receiver Multicoupler
While Rojone manufactures a huge antenna range, we also are partnered with companies who are leaders internationally.

Radiall and COJOT offer a specialised range of Military antennas & custom designs to client specification;
Handheld Antennas
Flexible VHF Blade Antennas, fully over-molded Broadband Antennas
Tape Blade Antennas
Man Portable Antennas
VHF/UHF 90 degree configuration antennas
Monopole 100-512MHz with gooseneck
Tube Antennas
Small Form Factor Antennas
Whip Dipped Low Profile antennas for Unmanned Sensors UAV’s
Swivel Mount Dipoles 1400-1800MHz UAV & ground station as well as tactical data link antenna
Ruggedised Vehicular Antennas
VHF/UHF Antennas
Spring Mounted 1800 MHz Dual Band Colinear array antennas
Custom antennas
PMR Antennas for Homeland Security Applications
Smart Array Antennas, Beam Steered, Phased Array, Active & steering circuits, sectorial &
COJOT Antenna Brochure
NATO Band Solutions 2016
WB2245 Datasheet
R380000178 Radiall Broadband Overmoulded Whip Antenna 225 – 512 Mhz 10w (296 kb)
Radiall Defence & Military Antenna Solution guide 3.0MB
R380990016-Radiall-Vehicle-Antenna-Base-Mount-2014.pdf (498 kb)
The R380.990.016 Antenna is a 70W, Dipolar Design, Broadband Vehicular Antenna. The Phase-Center is located near the middle of the Tubular Radome. The antennae is Ground plane Independent Antenna that can be Mast-Mounted without particular impact on Electrical Performances.
Omni-Directional Jammer Discone Antenna (AE-JD-1018) 398KB
The AE-JD-1018 Jammer Discone Antenna is a rugged all weather model, enclosed in an ABS radome, uses all ultra corrosion resistant aluminium alloy and does not require any field tuning or adjustments. The compact size of the omni-directional antenna allows easy handling, shipping and is highly suitable for transmitting & receiving without having the requirement of multiple antennas.
Bicone Antenna, Active Receive 10MHz to 2GHz (ROJ-130-x) 616KB
The ROJ-130-X is an Active Bicone Antenna originally designed for the Australian Navy for shipboard applications. It is primarily used as an active receive antenna for signals between 10MHz & 1GHz or 10MHz & 2GHz (the frequency is determined by the amplifier selected by the customer).
The system consists of 3 main parts – the Antenna, Coaxial Cable, and Power Supply Module
Ruggedized Wide Band Omni Discone Antenna 75-3000 MHz
The AE-WD75-3000 is wide band heavy duty welded discone antenna is specially designed to survive extreme environmental conditions. Its low VSWR through the entire 75-3000 MHz band makes this discone antenna suitable as a high efficiency transmitting and receiving antenna.
This antennas superior performance meets the broadband requirement of a base station antenna for spectrum monitoring or jamming applications without the need of multiple antennas.
Wide Band Omni Direction Discone Antenna
The AE-AWD100-3000 wide band discone antenna is specially designed for Omni-Directional coverage. Due to its low VSWR through the entire band 100-3000MHz this discone can be used as a transmitting and receiving antenna.
Its high efficiency meets the broadband requirement of a base station antenna forspectrum monitoring or jamming applications without the need of multiple antennas.
The AE-AED100-3000 wide band discone antenna is ruggedized for all weather conditions and does not require any field tuning or adjustment. The compact size of this discone antenna allows for easy handling and has specially designed mounting hardware for fast installation. The wide band discone antenna when packed comes with the cone and disc elements removed from the antenna body for easy shipment.
UHF Vehicle Antenna
Radiall is proud to introduce a new UHF Vehicular Antenna for military applications. Embedded on terrestrial or marine vehicles, the robust design is engineered to withstand harsh environments without compromising electrical performance.
Radiall’s UHF Vehicular Antennas are ideal when excellent electrical performance and reliability is required.
The main benefits and features of these UHF Vehicular Antennas include:
- Excellent electrical performance
- High robustness & reliability
- Small form factor





