Rojone Pty Ltd - Australia

Rojone — Wed, 22 Feb 2012 04:48:29 +0000

The HyperGain model A-PDA5158-28 is a high performance broadband solid dish antenna designed to operate from 5.1GHz to 5.8GHz (5125-5850 MHz). The wide band design of this antenna eliminates the need to purchase different antennas for each frequency. This simplifies installation since the same antenna can be used for a wide array of wireless applications. This antenna features 287 dBi of gain with a 6^o beam-width. It can be oriented for either vertical or horizontal polarisation.

This product is a suitable alternative to Andrews PX2F-52-NXA (Andrews is a registered trademark of CommScope).

A-PDA5158-28 – Parabolic Dish Antenna

EziTrak sponsors a car in Cancer Council’s Shitbox Rally

Rojone — Thu, 16 Feb 2012 23:11:18 +0000

EziTrak^® is thrilled to be involved with this year’s Shitbox Rally to raise money for The Cancer Council NSW. EziTrak^® is sponsoring the Team Tonka Toys vehicle in this event.

The Shitbox Rally takes shitty cars and attempts to drive them across Australia, raising money for The Cancer Council along the way. This year’s rally will start in Melbourne on April 14, 2012 and end in Cairns on April 20.

As a GPS Security and Tracking System, EziTrak^® is an ideal sponsor of the Team Tonka Toys vehicle and will be used by the team to track their progress up the east coast of Australia. EziTrak^® is an Australian designed and manufactured monitoring, protection and GPS tracking system giving vehicle owners personalised, self-monitoring. This early warning anti-theft device is interactive and has no monthly or annual monitoring fees.

EziTrak^® offers security, control, GPS tracking and emergency notification for a single one-off cost to vehicle owners. EziTrak^® vehicle monitoring, protection and tracking system is available directly from Rojone.

The Cancer Council NSW is a community funded and focused cancer charity dedicated to the defeat of cancer. Tax-deductible donations to this event are welcomed at;

http://www.everydayhero.com.au/team_tonka_toys

Rojone — Wed, 15 Feb 2012 02:53:29 +0000

Power over Ethernet (PoE) technology describes a system to pass electrical power safely, along with data, on Ethernet cabling. The IEEE standard for PoE requires Category 5 cable or higher for high power levels, but can operate with category 3 cable for low power levels. Power is supplied in common mode over 2 or more of the differential pairs of wires found in the Ethernet cables and comes from a power supply within a PoE-enabled networking device such as an Ethernet switch or can be injected into cable run with a midspan power supply.

Rojone is pleased to present our new PoE DC injector with surge protection built-in. This unit features ultra fast gas tubes and high current diodes for optimum performance. This is a must-have for all PoE devices for ultimate protection. This unit has been designed to be used with a huge variety of radio using up to 60vDC.

PoE Injector with Lightning Arrestor (model ROJ-99103)

Rojone — Thu, 02 Feb 2012 22:47:16 +0000

Rojone is proudly the sole Australian stocking representative for Satel Finland, high performance & ultra-reliable Radio Modems, both licenced & unlicensed options.

To complement our premium range of Radio Modems & in collaboration with industry leading positioning, surveying & machine control professionals, we have designed and manufactured a comprehensive selection of antennas, mountings & support products such as assemblies, cables & connectors to satisfy our surveying, positioning and machine control customers.

Quick Reference Selection Guide

Satel Radios Modems
SAT-3ASD-EASY	1W RADIO WITH LCD SCREEN
SAT-3ASD-EPIC	10W RADIO WITH LCD SCREEN
SAT-EASYPRO-5W	5W RADIO ONLY
SAT-EASYPRO-5W-PACK	5W RADIO COMPLETE WITH INTERFACE, PROGRAMMING & POWER CABLES
SAT-EASYPRO-5W-SAEPACK	5W RADIO PACK WITH SAE CONNECTOR POWER CABLE
SAT-EASYPRO-35W	35W RADIO ONLY
SAT-EASYPRO-PACK	35W RADIO COMPLETE WITH INTERACE, PROGRAMMING & POWER CABLES
SAT-EASYPRO-35W-SAEPACK	35W RADIO PACK WITH SAE CONNECTOR POWER CABLE

Satel Radio Accessories
SAT-NARS-1F-4A	1W & 10W 3ASD-EASY INTERFACE CABLE
SAT-CRS-9	1W & 10W 3ASD-EASY INTERFACE ADAPTOR
SAT-YPO320	1W 3ASD-EASY FIELD BATTERY PACKS
SAT-CRS-35W	5W & 35W YC0369 INTERFACE CABLE
SAT-PROG-35W	5W & 35W YC0363 PROGRAMMING CABLE
SAT-C-P-35W	5W & 35W YC0355 POWER CABLE
SAT-C-P-SAE-35W-4PIN	5W & 35W YC0352 SAE CONNECTORISED POWER CABLE
SAT-YC0368	35W DATA CABLE FOR NON-TOPCON DEVICES
SAT-EASY-TRIPOD-BAG	YN0925 TRIPOD BAG
SAT-EASY-CARY-BAG	5W & 35W YN0102 MODEM CARRY BAG

Antennas
SAT-EASYPRO-ANT	460 MHz, YA0103 ANTENNA TNC MALE
A-NMOWB450C	460 MHz, WHIP, NMO BASE FIELD TUNABLE 3.5-5.6dBi 9900-1068
A-326-460	460 MHz, GROUND INDEPENDENT 6dB ANTENNA
A-337-460-HD	460 MHz, HEAVY DUTY ANTENNA, BNC BASE PLUG
A-338-460-HD	460 MHz, HEAVY DUTY ANTENNA, TNC BASE PLUG
Antennas
A-380-06603A120-09	460 MHz, ELEVATED FEED 6dB ANTENNA,1/2″ 26TPI PAINTERS POLE MOUNT, 1.2MTRS LOW LOSS CABLE LMR195ULTRA, BNC MALE PLUG SUPPLIED SEPARATELY
A-380SP-HD-28A500-460	460 MHz, ELEVATED FEED 6dB ANTENNA, SPRING BASED, 5MTR LOW LOSS CABLE LMR240ULTRA, FME CONNECTOR, FME-UHF ADAPTOR
A-RJ-30-050503-01	460MHz, HEAVY DUTY WHIP, BNC MALE BASE
A-RJ-30-030012-01	915 MHz, HEAVY DUTY WHIP, TNC MALE REVERSE BASE
A-409-24H-915-HD	915 MHz, HEAVY DUTY ANTENNA, TNC MALE REVERSE POLARITY BASE CONNECTOR
A-ANT475-14A	NEXT G GLASS MOUNT ANTENNA, N MALE CONNECTOR ON CABLE TAIL
A-CD822MAG-5N	NEXT G MAGNETIC ANTENNA, N MALE CONNECTORS, 5MTR CABLE TAIL
A-409-03A-NG-HD	NEXT G HEAVY DUTY ANTENNA, BNC MALE BASE
L-LPT2400NMOF	2.4 GHz, 2 dBi ANTENNA, NMO BASE

Mounting Accessories
A-NMO38BASE	NMO ADAPTOR BASE, 5/8″ THREAD POLE MOUNTING, 5MTRS CABLE, TNC MALE PLUG
A-NMOMMRTNC	NMO MAGNETIC BASE, 4MTRS CABLE, TNC MALE CONNECTOR
A-NMOMMRTNREV	NMO MAGNETIC BASE, 4MTRS CABLE, TNC MALE REVERSE CONNECTOR
A-NMOMMRN	NMO MAGNETIC BASE, LOW LOSS RG58, N MALE CONNECTOR
A-SO239BASE	SO239 UHF FEMALE BASE, 5/8″ THREAD POLE MOUNT, 5MTRS CABLE TNC MALE PLUG
A-658-500-03A	BASE TO SUIT A-326-460 ANTENNA, 5MTR CABLE, BNC MALE PLUG

Specialized Cable Assemblies
CA-9063-1113	1.52MTR PROGRAMMING ASSEMBLY, DEUTSCH RECTANGULAR MULTIPIN CONNECTOR, TO 3 X 9 WAY D SUB PLUG, SOCKET CONTACT, & VEHICLE CIGARETTE LIGHTER ADAPTOR
CA-9060-5921	1.52MTR PROGRAMMING ASSEMBLY, MIL CIRCULAR 11 PIN PLUG, TO 9 WAY D SUB PLUG, SOCKET CONTACT, & VEHICLE CIGARETTE LIGHTER ADAPTO
CA-9063-1036-7M-A	7MTR LMR-400ULTRA ASSEMLBY N MALE EACH END (CA-05913M13M700-0809)
CA-9063-1069-15	15FT ANTENNA ASSEMBLY GPS ANT/MC CURLY CORD YELLOW
CA-9063-1069-25	25FT ANTENNA ASSEMBLY GPS ANT/MC COIL CORD YELLOW
CA-9063-1081-25	25FT ANTENNA ASSEMBLY DUAL GPS ANT/MC COIL CORD YELLOW
CA-9063-1073-30Y	30FT (9.144MTRS), RG213U ASSEMBLY N MALE EACH END, 110MM YELLOW SHRINK EACH END, DUST CAP AND CHAIN FITTED EACH END
CA-9063-1073-35	35FT (10.668MTRS), RG213U ASSEMBLY N MALE EACH END, DUST CAP AND CHAIN FITTED EACH END
CA-9063-1036-3M-TW	7MTR, TWINNED, KEVLAR SHEATHED N MALE- N MALE ONE BLACK SHEATH, ONE YELLOW SHEATH
CA-9063-1036-20-ROJ	20FT (6MTR) ASSEMBLY LMR400ULTRA, N MALE PLUGS EACH END, BLACK SHRINK
CA-9063-1036-20Y-ROJ	20FT (6MTR) ASSEMBLY LMR400ULTRA, N MALE PLUGS EACH END, YELLOW SHRINK

Installation Accessories
API-100082	SCAPA AMALGAMATING TAPE, 25mm X 10MTRS
TC-GP-GTRNFF	LIGHTNING ARRESTORS N FEMALE – N FEMALE
38.2-7.5/W	CABLE TIES WEATHERPROOF 382 X7.55 mm PKT OF 100
202-4.7/W	CABLE TIES WEATHERPROOF 202 X 4.7 mm PKT OF 100
152-3.5/W	CABLE TIES WEATHERPROOF 152 X 3.5 mm PKT OF 100

Coaxial Cables
CC-LMR-400	10mm 50 OHM LOW LOSS COAX
CC-LMR-400-ULTRA	10mm 50 OHM LOW LOSS ULTR FLEX COAX
CC-M17-128-RG400	5mm 50 OHM TEFLON COAX
CC-LMR-195-ULTRA	5mm 50 OHM LOW LOSS COAX

Connectors
	N Series
R-161082	N MALE CRIMP SUIT RG58
RC-161237	N FEMALE CRIMP SUIT RG58
R-161182	N MALE R/A CRIMP SUIT RG58
R-161075	N MALE CRIMP SUIT RG213U
RC-161241	N FEMALE CRIMP SUIT RG213U
R-161183	N MALE CRIMP SUIT RG400
TC-400-NMH	N MALE HEX CRIMP SUIT LMR-400-ULTRA/LMR-400
TC-EZ-400-NMH	N MALE EZI CRIMP FOR LMR-400
TC-400-NMH-RA	N MALE R/A HEX CRIMP SUIT LMR-400-ULTRA/LMR-400
TCC-400-NM	N MALE CRIMP SUIT LMR-400
TCC-400-NF	N FEMALE CRIMP SUIT LMR-400
TC-EZ-400-NF	N FEMALE EZI CRIMP FOR LMR-400
	TNC Series
R-143082-161	TNC MALE CRIMP SUIT RG58
API-B20-008	TNC FEMALE CRIMP SUIT RG58
PA-PE4678	TNC MALE R/A REVERSE CRIMP SUIT RG58
TCC-195-TFRP-BH	TNC FEMALE REVERSE CRIMP BULKHEAD SUIT RG58
R-143332-161	TNC FEMALE PANEL MOUNT BULKHEAD CRIMP SUIT RG58
R-143182-161	TNC R/A CRIMP SUIT RG58
	BNC Series
R-141082-161	BNC MALE CRIMP SUIT RG58
R-141237-161	BNC FEMALE CRIMP SUIT RG58
TC-400-BM	BNC MALE SUIT LMR-400
	Adaptors
PA-PE9595	N MALE-N FEMALE BULKHEAD ADAPTOR
R-161771	N MALE-N FEMALE RIGHT ANGLE ADAPTORS
R-161703	N MALE TO N MALE INLINE JOINER
PA-PE9389	N FEMALE-F MALE ADAPTORS
R-191511	N FEMALE-TNC MALE ADAPTORS
R-191421	N MALE-BNC FEMALE ADAPTORS
R-191405	BNC FEMALE-TNC MALE ADAPTORS
R-191419	BNC MALE-N FEMALE ADAPTOR
R-143704	TNC FEMALE-TNC FEMALE ADAPTOR
	Other Connectors
R-161853	N MALE DUSTCAP WITH CHAIN
R-280560	STRAIN RELIEF BOOTS BLACK SUIT RG174,RG316
R-280570	BOOTS BLACK SUIT RG58
MS3116-F12-3S	MIL CIRCULAR CONNECTORS

Heatshrink
HE-MA47-12-BK	12mm/3mm GLUE SHRINK 1.22 METRE LENGTH
HE-MA47-19-BK	19mm/6mm GLUE SHRINK 1.22 METRE LENGTH
HE-MA47-30-BK	30mm/8mm GLUE SHRINK 1.22 METRE LENGTH
HE-MA47-40-BK	40mm/12mm GLUE SHRINK 1.22 METRE LENGTH
HE-MA47-50-BK	50mm/16mm GLUE SHRINK 1.22 METRE LENGTH
HE-MA47-63-BK	63mm/19mm GLUE SHRINK 1.22 METRE LENGTH
HE-MA47-75-BK	75mm/22mm GLUE SHRINK 1.22 METRE LENGTH
HE-MA47-95-BK	95mm/30mm GLUE SHRINK 1.22 METRE LENGTH
HE-MA47-115-BK	115mm/34mm GLUE SHRINK 1.22 METRE LENGTH
HE-MA47-140-BK	140mm/42mm GLUE SHRINK 1.22 METRE LENGTH
KUHS-225G-1.2-BK	1.4mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-1.5-BK	2.0mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-2-BK	2.5mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-3-BK	3.4mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-4.5-BK	5.0mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-5-BK	5.6mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-6-BK	6.5mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-9-BK	9.8mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-12-BK	12.5mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-15-BK	15.6mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-18-BK	19.0mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-25-BK	25.0mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-30-BK	31mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-38-BK	39mm STANDARD SHRINK – OTHER COLOURS AVAIL
KUHS-225G-50-BK	51mm STANDARD SHRINK – OTHER COLOURS AVAIL

Patch Panels

Rojone — Mon, 19 Dec 2011 03:51:33 +0000

Patch Panels - 1 & 2 RU Stainless Steel suitable for N Type Bulkhead Connectors.

Rojone has fabricated some standard patch panels to meet specific customer requirements.

Standard product has evolved from this range resulting in both 1 RU and 2 RU 304 Polished Stainless Steel patch panels to accommodate both front and rear mounting N Type panel mount connectors. Hole configurations are available in 4, 6, 8, 12 for the 1 RU panels and 24 holes in the 2 RU version. Currently the panels have either a polished or painted finsh, but can be custom finished according to your specific requirements.

New SilverLine-VNA Cables (18, 26.5 and 40 GHz)

Rojone — Wed, 02 Nov 2011 01:48:21 +0000

SilverLine-VNA is a rugged and durable test cable ideal for use with Vector Network Analyser’s and other test equipment in the lab and factory. An enhanced version of Times Microwave’s SilverLine test cables, these cables are protected with a torque and crush resistant stainless steel armour which results in exceptional phase and amplitude stability with bending. 18, 26.5 and new 40 GHz low loss cable versions are available.

The braided PET outer jacket makes SilverLine-VNA easy to handle, non-conductive and improves flexibility when compared with extruded jackets. The chrome plated metal back shells maintain the integrity of the cable to connector interface and provide a distinctive appearance.

Features and benefits;

18.0, 26.5 cable
Introducing the new 40 GHz cable
125^OC operation
Phase, Loss & VSWR stable
High flex life
Torque and crush resistant stainless steel armor
Chrome plated metal strain relief back shells
ROHS compliant

The full range of products from Times Microwave Systems are available through Rojone Pty Ltd.

New Prep Tool for LMR-240 Low Loss Coaxial Cables from Times Microwave

Rojone — Tue, 25 Oct 2011 23:07:33 +0000

Times Microwave Systems has recently introduced the new CST-240 All-In-One Combination Prep Tool for use with LMR-240 low loss coaxial cables. The new tool provides the following features and advantages:

- Combination feature allows preparation of LMR-240 cables for either straight or right angle crimp connector attachment
- Suitable for use with most LMR-240 connectors
-Provides consistently sharp cut of dielectric for best VSWR performance
- Rugged, lightweight construction
- Lanyard attachment included

New Prep Tool for LMR-500 Low Loss Coaxial Cables from Times Microwave

Rojone — Tue, 25 Oct 2011 23:03:26 +0000

Times Microwave Systems has recently introduced the new CST-500 All-In-One Combination Prep Tool for use with LMR-500 low loss coaxial cables. The new tool provides the following features and advantages:

- Combination feature allows preparation of LMR-500 cables for either crimp or clamp connector attachment
- Suitable for use with all LMR-500 connectors
- Provides consistently sharp cut of dielectric for best VSWR performance
- Includes a built-In debur tool eliminating the need for a separate debur tool
- Rugged, lightweight construction
- Lanyard attachment included

New Prep Tools for LMR-400-75 & LMR-600-75 Low Loss Coaxial Cables from Times Microwave

Rojone — Tue, 25 Oct 2011 22:50:56 +0000

Times Microwave Systems has recently introduced the new CST-400-75 All-In-One Combination Prep Tool for use with LMR-400-75 low loss coaxial cables.

The CST-400-75 tool provides the following features and advantages:

- Suitable for use with all LMR-400-75 connectors
- Provides consistently sharp cut of dielectric for best VSWR performance
- Rugged, lightweight construction
- Includes a built-In debur tool eliminating the need for a separate debur tool
- Lanyard attachment included (not shown)

The ST-600-75 Prep Tool (3190-090) is suitable for use with LMR-600-75 low loss coaxial cables and connectors.

Rojone — Wed, 05 Oct 2011 22:59:13 +0000

Signal Blanking Device

Specifications:

Part No API-BNCF-1N649CP-BNCM
Diode Orientation Cathode-band to centre pin

Part No API-BNCF-1N649AS-BNCM
Diode Orientation Anode to shield

Description                        Used for Blanking Signal
Frequency                          N/A
Connector                          BNC Female to BNC Male
Impedance                         50 Ohms